CompTIA A+ Core 1 · 220-1201

Objective 2.2: Wireless networking technologies

Try it now: 8 quick questions on this objective, no account needed.

Objective 2.2 · Wireless technologies

1 / 8
Recall

802.11n

Which max speed?

Practice questions for A+ Core 1 objective 2.2, “Wireless networking technologies.” Every question is original, written to the 220-1201 exam objectives, and comes with a full explanation — answer them below to see instant grading.

This objective sits in Domain 2.0: Networking, which is about 23% of the exam — so mastering it moves your readiness score meaningfully.

More 2.2 practice questions

Objective 2.2 · practice questions

1 / 5
Exam style

Which IEEE 802.11 standard introduced Wi-Fi 6 and operates on both 2.4 GHz and 5 GHz bands with OFDMA technology?

All 5 questions, with answers
  1. 1.Which IEEE 802.11 standard introduced Wi-Fi 6 and operates on both 2.4 GHz and 5 GHz bands with OFDMA technology?

    • A.802.11ac
    • B.802.11n
    • C.802.11ax
    • D.802.11g

    Answer: C. 802.11ax. 802.11ax, marketed as Wi-Fi 6, introduced OFDMA (Orthogonal Frequency Division Multiple Access) to improve efficiency in dense environments with many simultaneous clients. It operates on both 2.4 GHz and 5 GHz and significantly increases throughput and reduces latency compared to its predecessor 802.11ac (Wi-Fi 5). Wi-Fi 6E extends 802.11ax to the 6 GHz band as well.

  2. 2.Which wireless standard operates exclusively on the 5 GHz band and introduced MU-MIMO and beamforming for maximum theoretical speeds of nearly 7 Gbps?

    • A.802.11n
    • B.802.11g
    • C.802.11ac
    • D.802.11ax

    Answer: C. 802.11ac. 802.11ac (Wi-Fi 5) operates exclusively on the 5 GHz band and introduced downlink MU-MIMO (Multi-User MIMO), allowing an AP to transmit to multiple clients simultaneously, along with beamforming to focus the signal toward specific clients. Maximum theoretical throughput on 802.11ac wave 2 reaches approximately 6.9 Gbps with 160 MHz channels and 8x8 MU-MIMO. 802.11ax (Wi-Fi 6) subsequently improved on this with OFDMA on both bands.

  3. 3.Which 802.11 standard was the first to support operation exclusively on the 5 GHz band, offering speeds up to 54 Mbps?

    • A.802.11b
    • B.802.11g
    • C.802.11a
    • D.802.11n

    Answer: C. 802.11a. 802.11a was released simultaneously with 802.11b and operated exclusively in the 5 GHz band with a maximum data rate of 54 Mbps. Because it operated at 5 GHz, it avoided interference from 2.4 GHz devices but had reduced range compared to 802.11b. 802.11g brought 54 Mbps to the 2.4 GHz band and was backward compatible with 802.11b.

  4. 4.A conference centre upgrades its wireless network from 802.11ac to 802.11ax. Users in a crowded expo hall with hundreds of simultaneous wireless devices report significantly better performance. What 802.11ax feature is responsible for this improvement?

    • A.Beamforming exclusive to 802.11ax
    • B.OFDMA allowing the AP to serve multiple clients simultaneously in each transmission
    • C.Operation on the 60 GHz band for higher throughput
    • D.Elimination of the 2.4 GHz band to reduce interference

    Answer: B. OFDMA allowing the AP to serve multiple clients simultaneously in each transmission. OFDMA (Orthogonal Frequency Division Multiple Access) is a key feature of 802.11ax (Wi-Fi 6) that subdivides a channel into smaller resource units (RUs) and assigns different RUs to different clients in the same transmission, dramatically improving efficiency in high-density environments. 802.11ac uses OFDM which serves only one client per transmission. 802.11ax operates on both 2.4 GHz and 5 GHz, not 60 GHz (which is 802.11ad/WiGig).

  5. 5.A new smart thermostat can't find the office Wi-Fi during setup, although phones and laptops connect fine. The thermostat supports only 2.4 GHz, and the access point broadcasts the network on 5 GHz only. What should the technician do?

    • A.Move the 5 GHz network to a DFS channel
    • B.Widen the 5 GHz channel to 160 MHz
    • C.Turn on the 2.4 GHz band for the network
    • D.Change the security from WPA3 to WEP

    Answer: C. Turn on the 2.4 GHz band for the network. Many smart-home devices have 2.4 GHz radios only, so they can't see a network broadcast only on 5 GHz; turning on the 2.4 GHz band, often as a separate network name for such devices, lets the thermostat join. DFS channels and channel width are still 5 GHz, which the thermostat can't use, and WEP is obsolete and insecure, so it should never be the fix.

Learn 2.2 and every other objective

Your A+ Core 1 path walks the whole exam in short stops, one objective at a time, and maps where you stand as you go.

Start my A+ Core 1 path

No account needed to start.

More objectives in Domain 2.0

← All A+ Core 1 220-1201 objectives