CompTIA A+ Core 1 · 220-1201

Objective 2.8: Networking tools and what they're for

Try it now: 8 quick questions on this objective, no account needed.

Objective 2.8 · Networking tools

1 / 8
Quick scenario

A technician needs to terminate a Cat6 Ethernet cable with an RJ-45 connector. Which tool is required for this task?

Practice questions for A+ Core 1 objective 2.8, “Networking tools and what they're for.” Every question is original, written to the 220-1201 exam objectives, and comes with a full explanation — answer them below to see instant grading.

This objective sits in Domain 2.0: Networking, which is about 23% of the exam — so mastering it moves your readiness score meaningfully.

More 2.8 practice questions

Objective 2.8 · practice questions

1 / 5
Exam style

A technician needs to trace an unlabelled network cable through a wall to identify which patch panel port it terminates at. Which tool should be used?

All 5 questions, with answers
  1. 1.A technician needs to trace an unlabelled network cable through a wall to identify which patch panel port it terminates at. Which tool should be used?

    • A.Cable tester
    • B.Wi-Fi analyser
    • C.Toner probe (tone generator and probe)
    • D.Loopback plug

    Answer: C. Toner probe (tone generator and probe). A tone generator injects a signal onto the cable at one end, and the probe (inductive amplifier) is used at the patch panel or other suspected termination point to audibly detect the tone, identifying the correct cable without cutting into the wall. A cable tester verifies continuity and wiring order but cannot trace an unlabelled cable through walls. A Wi-Fi analyser is used for wireless networks, not physical cable tracing.

  2. 2.A technician wants to verify that a network card is functioning correctly without connecting it to any network device. Which tool should be used?

    • A.Cable tester
    • B.Punchdown tool
    • C.Wi-Fi analyser
    • D.Loopback plug

    Answer: D. Loopback plug. A loopback plug connects a device's transmit pins directly to its receive pins, allowing the NIC or port to send and receive test data to itself, confirming the hardware is functional independently of any external network. A cable tester checks the continuity and pinout of a network cable, not a NIC. Wi-Fi analysers are for wireless network diagnostics.

  3. 3.A technician cannot determine where a cable jacket ends and the twisted pairs begin because the outer jacket is stuck. What tool is appropriate for removing the outer jacket of a network cable without damaging the inner wire insulation?

    • A.Wire cutters
    • B.Crimper
    • C.Cable stripper
    • D.Punchdown tool

    Answer: C. Cable stripper. A cable stripper (also called a jacket stripper or wire stripper set for data cables) is specifically designed to cut through the outer jacket at a controlled depth, preventing the inner wire insulation from being nicked or damaged. Using regular wire cutters risks cutting too deep and nicking the wire conductors, which can cause intermittent faults. The crimper is used after stripping to attach the RJ-45 connector.

  4. 4.After installing a wireless network in a multi-tenant office building, a technician needs to identify neighbouring APs, their channels, and signal strengths. Which tool is appropriate?

    • A.Toner probe
    • B.Wi-Fi analyser
    • C.Cable tester
    • D.Network tap

    Answer: B. Wi-Fi analyser. A Wi-Fi analyser (available as a software app or dedicated hardware device) scans the wireless environment and displays all visible access points, their SSIDs, channels, signal strength (RSSI), and security type. This information is essential for identifying channel conflicts and optimising AP placement and channel assignments. A toner probe is for physical cable tracing, and a cable tester checks wired cable integrity.

  5. 5.A technician suspects a cable run has a wiring fault (reversed pairs or split pairs) after users report intermittent connectivity. Which tool will confirm this?

    • A.Toner probe
    • B.Loopback plug
    • C.Cable tester
    • D.Multimeter

    Answer: C. Cable tester. A cable tester sends a signal through each wire pair and displays the pinout mapping, immediately identifying faults such as opens (broken wires), shorts, reversed pairs, split pairs, or crossed connections. A toner probe identifies which cable is which but does not test wiring integrity. A loopback plug tests a port, not the cable run between two termination points.

Learn 2.8 and every other objective

Your A+ Core 1 path walks the whole exam in short stops, one objective at a time, and maps where you stand as you go.

Start my A+ Core 1 path

No account needed to start.

More objectives in Domain 2.0

← All A+ Core 1 220-1201 objectives