CompTIA A+ Core 1 · 220-1201

Objective 3.4: Storage devices

Try it now: 8 quick questions on this objective, no account needed.

Objective 3.4 · Storage devices

1 / 8
Recall

CD-ROM / CD-RW

Which max speed?

Practice questions for A+ Core 1 objective 3.4, “Storage devices.” Every question is original, written to the 220-1201 exam objectives, and comes with a full explanation — answer them below to see instant grading.

This objective sits in Domain 3.0: Hardware, which is about 25% of the exam — so mastering it moves your readiness score meaningfully.

More 3.4 practice questions

Objective 3.4 · practice questions

1 / 5
Exam style

A database server requires storage with the lowest possible random read latency for transaction processing. Which storage solution is best?

All 5 questions, with answers
  1. 1.A database server requires storage with the lowest possible random read latency for transaction processing. Which storage solution is best?

    • A.15,000 RPM SAS HDD
    • B.SATA SSD
    • C.NVMe SSD (PCIe Gen 4)
    • D.RAID 5 array of 7200 RPM HDDs

    Answer: C. NVMe SSD (PCIe Gen 4). NVMe SSDs on PCIe Gen 4 achieve random read latencies of under 100 microseconds and extremely high IOPS, far exceeding SATA SSDs and spinning disks for database transaction workloads. SATA SSDs offer much better latency than HDDs but are constrained by the SATA interface. RAID 5 with HDDs improves sequential throughput but does not address the inherent rotational latency of spinning disks.

  2. 2.A RAID 5 array consists of five 4 TB drives. One drive fails and is replaced. During the rebuild, a second drive fails. What is the result?

    • A.The array rebuilds using the parity from the remaining drives
    • B.The array continues operating in degraded mode
    • C.All data on the array is lost
    • D.The second failed drive's data is preserved on the hot spare

    Answer: C. All data on the array is lost. RAID 5 can tolerate only a single drive failure at a time; a second drive failure during rebuild results in complete data loss because parity information from the first failed drive is still being reconstructed. This is why the rebuild window on large drives is considered a risk period. RAID 6 tolerates two simultaneous failures using dual parity.

  3. 3.Which drive interface is built for enterprise servers, connects through a host bus adapter or RAID controller, and offers dual ports so a drive stays reachable if one path fails?

    • A.SAS
    • B.SATA
    • C.eSATA
    • D.mSATA

    Answer: A. SAS. Serial Attached SCSI (SAS) is the server interface: drives connect through SAS host bus adapters or RAID controllers, and enterprise SAS drives have two ports that can be cabled to two controllers for redundancy. SATA, eSATA and mSATA drives have a single port and are aimed at desktops, external enclosures and laptops.

  4. 4.A technician is installing an M.2 drive and notices the slot is labeled "M.2 2280." What do the numbers 2280 represent?

    • A.The drive's maximum speed in MB/s
    • B.The width and length of the module in millimeters
    • C.The PCIe generation and lane count
    • D.The SATA revision number

    Answer: B. The width and length of the module in millimeters. M.2 module naming uses the format where the first two digits are the width (22mm) and the remaining digits are the length (80mm), so 2280 is 22mm wide and 80mm long — the most common M.2 size. Other common lengths include 2242 and 2260. The naming does not indicate speed or interface type.

  5. 5.A system builder installs a new M.2 NVMe SSD and a SATA SSD simultaneously. After installation, only the SATA SSD appears in the BIOS. What is most likely the cause?

    • A.The NVMe SSD is defective
    • B.The M.2 slot shares lanes with a SATA port and enabling both creates a conflict
    • C.NVMe SSDs require a device driver installed before the BIOS can detect them
    • D.SATA and NVMe cannot coexist in the same system

    Answer: B. The M.2 slot shares lanes with a SATA port and enabling both creates a conflict. On many consumer motherboards, the M.2 slot shares PCIe or SATA lanes with physical SATA ports; enabling both devices simultaneously can cause a conflict where the motherboard disables one interface. The motherboard manual documents which SATA ports are disabled when the M.2 slot is populated. Drivers are not required for BIOS-level drive detection, and SATA/NVMe coexistence is normally supported if lane conflicts are avoided.

Learn 3.4 and every other objective

Your A+ Core 1 path walks the whole exam in short stops, one objective at a time, and maps where you stand as you go.

Start my A+ Core 1 path

No account needed to start.

More objectives in Domain 3.0

← All A+ Core 1 220-1201 objectives